Moblite7 HDZero 75mm BNF

$229.99

Control Protocol

Delivery and Shipping

Add some general information about your delivery and shipping policies.

This is one of the first 75mm aircraft equiped with HDZero video transmission. It is now discontinued, but interestingly carries the HDZero Lite camera, which has slightly better picture than the lighter alternatives that were subsequently released. 

Specifications:
Brand Name: Happymodel
Model: Moblite7 HDZERO
Frame wheelbase: 75mm
Weight: 29.5 gram without battery
Size: 98mm*98mm*50mm
Receiver option:
SPI ELRS 2.4GHz
SPI FRSKY 2.4GHz
Compatible with 1S Lipo battery or Lihv battery
Battery Plug: PH2.0

Package includes:

Item Name Qty
Mobula7 v4 75mm frame +Canopy 1
SPI Receiver Option1: SuperbeeF4 Lite FC built-in ExpressLRS SPI RX 1
SPI Receiver Option2: SuperbeeF4 Lite FC built-in Frsky SPI RX
EX1002 KV20000 Unibell brushless motor 4
Gemfan 1610-2 bi-blades propeller(4cw+4ccw) 1
HDZero Nano Lite Camera 1
HDZero Whoop Lite VTX 1
Spare Canopy 1
Propeller disassemble tool 1
Screw driver 1
Flight controller
SuperbeeF4 Lite ELRS/FRSKY
SPI ELRS version Firmware target: CrazybeeF4SX1280
SPI FRSKY version Firmware target: CrazybeeF4FR
MCU:STM32F411CEU6 (100MHz, 512K FLASH)
Sensor: ICM20689 or ICM42688P or BMI270(SPI connection)
Power supply: 1S Lipo Lihv battery input (DC 2.8V~4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in SPI Frsky/ExpressLRS receiver
Built-in 5V 1A BEC
Built-in voltage detection
Onboard 4in1 ESC MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV (2.8v~4.35v)
Currents: 5A continuous peak 6A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT150/DSHOT300/DSHOT600
Onboard SPI ExpressLRS 2.4GHz Receiver Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHz
Telemetry output Power: <12dBm
Receiver protocol:  SPI ExpressLRS
Could bind with ELRS V2.0 firmware TX module
Onboard Frsky SPI D8 /D16 2.4GHz Receiver SPI BUS receiver Frsky D8/D16 compatible
Compatible Non EU transmitter D8 model and EU-LBT(Frsky_x_lbt)
Channels: 8ch or 16ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
Based on CC2500 RF module Compatible with Futaba S-FHSS , Redpine protocol
Motor Model: EX1002 20000KV
Configu-ration:9N12P
Stator Diameter:10mm
Stator Length:2mm
Shaft Diameter:Φ1.5mm
Motor Dimension(Dia.*Len):Φ13.5mm*12.5mm
Weight(g):2.5g
No.of Cells(Lipo):1S only
Propeller Gemfan 1610-2 Bi-blades Weight:0.24g
Material: PC
Pitch:1 inchProps Dia:40mm
Center Hole Dia:1.5mm
HDZero Nano Lite Camera 14x16x11 mm
1.5gram
0.5 inch, up to 10650 mV/Lux-sec ultra-high sensitive CMos sensor
Excellent low light performance
Fov:
4:3: D:130° H:108° v:84°
16:9:D:122° H:108° V:65°
HDZero Whoop Lite VTX 1S Input
25mW/200mW RF Output-SmartAudio Support
25.5×25.5 M2 Soft Mounting- Antenna Retention
Removable Shielding Box- 32.5×32.5mm(29x29mm inner)
4.5grams/4mm Thickness (without shielding)
EXTINCT

Moblite7 HDZero 75mm BNF

$229.99

This is one of the first 75mm aircraft equiped with HDZero video transmission. It is now discontinued, but interestingly carries the HDZero Lite camera, which has slightly better picture than the lighter alternatives that were subsequently released. 

Specifications:
Brand Name: Happymodel
Model: Moblite7 HDZERO
Frame wheelbase: 75mm
Weight: 29.5 gram without battery
Size: 98mm*98mm*50mm
Receiver option:
SPI ELRS 2.4GHz
SPI FRSKY 2.4GHz
Compatible with 1S Lipo battery or Lihv battery
Battery Plug: PH2.0

Package includes:

Item Name Qty
Mobula7 v4 75mm frame +Canopy 1
SPI Receiver Option1: SuperbeeF4 Lite FC built-in ExpressLRS SPI RX 1
SPI Receiver Option2: SuperbeeF4 Lite FC built-in Frsky SPI RX
EX1002 KV20000 Unibell brushless motor 4
Gemfan 1610-2 bi-blades propeller(4cw+4ccw) 1
HDZero Nano Lite Camera 1
HDZero Whoop Lite VTX 1
Spare Canopy 1
Propeller disassemble tool 1
Screw driver 1
Flight controller
SuperbeeF4 Lite ELRS/FRSKY
SPI ELRS version Firmware target: CrazybeeF4SX1280
SPI FRSKY version Firmware target: CrazybeeF4FR
MCU:STM32F411CEU6 (100MHz, 512K FLASH)
Sensor: ICM20689 or ICM42688P or BMI270(SPI connection)
Power supply: 1S Lipo Lihv battery input (DC 2.8V~4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in SPI Frsky/ExpressLRS receiver
Built-in 5V 1A BEC
Built-in voltage detection
Onboard 4in1 ESC MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV (2.8v~4.35v)
Currents: 5A continuous peak 6A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT150/DSHOT300/DSHOT600
Onboard SPI ExpressLRS 2.4GHz Receiver Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHz
Telemetry output Power: <12dBm
Receiver protocol:  SPI ExpressLRS
Could bind with ELRS V2.0 firmware TX module
Onboard Frsky SPI D8 /D16 2.4GHz Receiver SPI BUS receiver Frsky D8/D16 compatible
Compatible Non EU transmitter D8 model and EU-LBT(Frsky_x_lbt)
Channels: 8ch or 16ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
Based on CC2500 RF module Compatible with Futaba S-FHSS , Redpine protocol
Motor Model: EX1002 20000KV
Configu-ration:9N12P
Stator Diameter:10mm
Stator Length:2mm
Shaft Diameter:Φ1.5mm
Motor Dimension(Dia.*Len):Φ13.5mm*12.5mm
Weight(g):2.5g
No.of Cells(Lipo):1S only
Propeller Gemfan 1610-2 Bi-blades Weight:0.24g
Material: PC
Pitch:1 inchProps Dia:40mm
Center Hole Dia:1.5mm
HDZero Nano Lite Camera 14x16x11 mm
1.5gram
0.5 inch, up to 10650 mV/Lux-sec ultra-high sensitive CMos sensor
Excellent low light performance
Fov:
4:3: D:130° H:108° v:84°
16:9:D:122° H:108° V:65°
HDZero Whoop Lite VTX 1S Input
25mW/200mW RF Output-SmartAudio Support
25.5×25.5 M2 Soft Mounting- Antenna Retention
Removable Shielding Box- 32.5×32.5mm(29x29mm inner)
4.5grams/4mm Thickness (without shielding)

Control Protocol

  • FRSKY
View product
×

A Message from Mr. Tiny Whoop

about Tariffs and Pricing

Hey everyone,

I’m speaking to you now both as a business owner and a member of the FPV family we've built together.

For almost ten years now, I’ve been doing everything I can to keep Tiny Whoop prices steady, even as costs started to rise. But with the newest wave of tariffs—more than doubling the cost of nearly every part we import from China—that fight has hit a wall.

Lots of you have already noticed some prices going up across the site. This isn’t a price hike to chase profit. It’s survival mode. Like everyone in the FPV industry right now, I’m facing a set of changes that hit fast and hard. Nearly everything we source from China now costs us more than double.

For an irresponsibly long time I ate the costs of the tariffs, but the math doesn’t work anymore without putting Tiny Whoop at serious risk.

So here’s what I want you to know:
Every price increase is a response to real, unavoidable costs.
Even with the price increases I’m taking a big hit.
When this pressure eases, I’ll roll back prices immediately.

If you have any questions or ideas it would mean a lot to hear from you!

We’re still shipping every day, still guaranteeing satisfaction on all orders. But this is the toughest moment Tiny Whoop has faced in nearly a decade.

Through all of this, my mission hasn’t changed. I’m still committed to helping people experience the gift of flight, to keeping TinyWhoop.com on the leading edge of innovation, and to making sure the magic of Tiny Whoop doesn’t get swallowed up by politics and global economics.

If you’ve been a part of this ride in any way, I am so, so grateful! Thank you for supporting Tiny Whoop, thank you for supporting my family, and thank you for being a part of this amazing community!

— Jesse Perkins
Founder, Tiny Whoop