1 6

SuperX - ELRS Analog FC with Integrated VTX

$80.40
Style

Delivery and Shipping

Add some general information about your delivery and shipping policies.

This is the replacement of the beloved Super Bee flight controller. There are two versions of this flight controller. This one comes with a built in VTX as well as an OSD chip for analog whoops. This flight controller comes stock, in the Mobula6 2024. This flight controller comes with the GNB A30 connector which will work with the BT2.0 plug.

You can find the HD version of this flight controller right HERE!

THE V2 BOARD IS THE SAME AS THE V1. IT JUST COMES WITH MOTOR PLUGS SOLDERED ON TO THE BOARD.

Flight controller SuperX ELRS AIO 5-IN-1 Flight controller
MCU:STM32F411CEU6 (100MHZ, 512K FLASH) ,ESP32-PICO-D4
Sensor:BMI270(SPI connection)
Mount hole size: 25.5mm*25.5mm
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G OpenVTX 0mw~400mw (MSP control)
Built-in UART ExpressLRS v3.0.0
Built-in voltage meter sensor , voltage meter scale 110
Built-in current meter sensor , current meter scale 1175
Onboard 4in1 ESC Power supply: 1S LiPo/LiPo HV
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: Bluejay v0.19.2
Default protocol: DSHOT300
Recommend ESC Startup power value to min1100/max1200
Onboard Serial ExpressLRS receiver Packet Rate option: 50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware version: V3.0
RF Frequency: 2.4GHz
Antenna : Enameled copper wire antenna
Telemetry output Power: <12dBm
Receiver protocol: Serial_based CRSF
Compatible with ExpressLRS V3.x.x TX Module
Could flash single ELRS receiver firmware by Wifi
ExpressLRS firmware target: ExpressLRS firmware target:
HappyModel AIO 2.4GHz RX+VTX (ExpressLRS web flasher)
Available from Expresslrs version 3.4.0 RC2
Onboard 5.8g VTX Firmware version: OPENVTX
MSP VTX
PIT Mode support
Channels:40ch
Transmitting Power: 0/RCE/25mw/100mw/400mw
Power supply: DC 5V
Current (5v): <650ma (400mw)
Antenna connector: U.FL

Our Collections

Happymodel

SuperX - ELRS Analog FC with Integrated VTX

$80.40

This is the replacement of the beloved Super Bee flight controller. There are two versions of this flight controller. This one comes with a built in VTX as well as an OSD chip for analog whoops. This flight controller comes stock, in the Mobula6 2024. This flight controller comes with the GNB A30 connector which will work with the BT2.0 plug.

You can find the HD version of this flight controller right HERE!

THE V2 BOARD IS THE SAME AS THE V1. IT JUST COMES WITH MOTOR PLUGS SOLDERED ON TO THE BOARD.

Flight controller SuperX ELRS AIO 5-IN-1 Flight controller
MCU:STM32F411CEU6 (100MHZ, 512K FLASH) ,ESP32-PICO-D4
Sensor:BMI270(SPI connection)
Mount hole size: 25.5mm*25.5mm
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G OpenVTX 0mw~400mw (MSP control)
Built-in UART ExpressLRS v3.0.0
Built-in voltage meter sensor , voltage meter scale 110
Built-in current meter sensor , current meter scale 1175
Onboard 4in1 ESC Power supply: 1S LiPo/LiPo HV
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: Bluejay v0.19.2
Default protocol: DSHOT300
Recommend ESC Startup power value to min1100/max1200
Onboard Serial ExpressLRS receiver Packet Rate option: 50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware version: V3.0
RF Frequency: 2.4GHz
Antenna : Enameled copper wire antenna
Telemetry output Power: <12dBm
Receiver protocol: Serial_based CRSF
Compatible with ExpressLRS V3.x.x TX Module
Could flash single ELRS receiver firmware by Wifi
ExpressLRS firmware target: ExpressLRS firmware target:
HappyModel AIO 2.4GHz RX+VTX (ExpressLRS web flasher)
Available from Expresslrs version 3.4.0 RC2
Onboard 5.8g VTX Firmware version: OPENVTX
MSP VTX
PIT Mode support
Channels:40ch
Transmitting Power: 0/RCE/25mw/100mw/400mw
Power supply: DC 5V
Current (5v): <650ma (400mw)
Antenna connector: U.FL

Style

  • V1 No motor plugs
  • V2.1 with motor plugs
View product
Back to top
×

A Message from Mr. Tiny Whoop

about Tariffs and Pricing

Hey everyone,

I’m speaking to you now both as a business owner and a member of the FPV family we've built together.

For almost ten years now, I’ve been doing everything I can to keep Tiny Whoop prices steady, even as costs started to rise. But with the newest wave of tariffs—more than doubling the cost of nearly every part we import from China—that fight has hit a wall.

Lots of you have already noticed some prices going up across the site. This isn’t a price hike to chase profit. It’s survival mode. Like everyone in the FPV industry right now, I’m facing a set of changes that hit fast and hard. Nearly everything we source from China now costs us more than double.

For an irresponsibly long time I ate the costs of the tariffs, but the math doesn’t work anymore without putting Tiny Whoop at serious risk.

So here’s what I want you to know:
Every price increase is a response to real, unavoidable costs.
Even with the price increases I’m taking a big hit.
When this pressure eases, I’ll roll back prices immediately.

If you have any questions or ideas it would mean a lot to hear from you!

We’re still shipping every day, still guaranteeing satisfaction on all orders. But this is the toughest moment Tiny Whoop has faced in nearly a decade.

Through all of this, my mission hasn’t changed. I’m still committed to helping people experience the gift of flight, to keeping TinyWhoop.com on the leading edge of innovation, and to making sure the magic of Tiny Whoop doesn’t get swallowed up by politics and global economics.

If you’ve been a part of this ride in any way, I am so, so grateful! Thank you for supporting Tiny Whoop, thank you for supporting my family, and thank you for being a part of this amazing community!

— Jesse Perkins
Founder, Tiny Whoop